-
product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
product
MIL-STD-1553 Test & Simulation Instrument for PXI
PXI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Time Synchronization to PXI 10MHz reference clock - Real-Time recording and physical bus rep...show more -
product
ICT Test Probes
C.C.P. Contact Probes Co., LTD.
Our In-Circuit Test Probes are used for all kinds of PCB tests. We offer a standard portfolio as well as customized parts.
-
product
Engineering Test & Development Tools
Besides DG’s aftermarket diagnostic tools, DG Technologies also offers several engineering tools for vehicle network development. DG’s hardware and software products are used by a variety of engineering customers such as test engineers, production engineers, and fiber optic testers. Our customers use DG interfaces for manipulating messages, datalogging, and ECU end-of-line testing over various multiplex networks.
-
product
Test & Measurement Automation Services
Our flexible and collaborative approach delivers efficient, accurate, and robust test systems, as well as the tools to leverage test data for effective results analysis. We develop systems using a variety of software and hardware platforms (custom and off-the-shelf), data acquisition systems, and control methods. We are comfortable developing custom turnkey systems or working alongside your team on your current system under development.
-
product
Flexible Probearm for HBM and Flex-Pitch Applications
TPA-GFG
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Flexible rotation of the probearm by precision gear 80:1*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
product
Water Meter Test Bench
VM-DN15-25
Shanghai Powoo Industry Develop Group Limited
The tester bench is the necessary measure instrument for the test and repair of water meter in metrological service, water meter manufacture, water supply company, industrial and mining establishments.
-
product
Dynamometer Test Systems
Genuen provides a full range of off-the-shelf and custom dyno test cell solutions. We offer turnkey test cell integration services and test cell upgrades and modernization for all types of dynamometers used in automotive, aerospace, industrial, commercial, off-highway, and agricultural markets. Our broad-based expertise includes dynamometer test systems ranging from AC motor, hydrokinetic, hydrostatic, electric AC/DC, eddy current, and hysteresis brake.
-
product
Fibre Channel Simulator & Analyzer Applications Software
fcXplorer Simulyzer
Avionics Interface Technologies
FC-1, FC-2, and FC4 Analyzer modes and displays - Frame parser for custom display of FC frames and payload data - Captured data can be saved as binary or “csv” files - User-defined trigger and filter features - “Live Capture” real-time display - Error detection and reproduction - Complete control of the transmit link - Replay of recorded data with precision timing or corrected protocol timing - Special testing functions such as defining command/response for exchange management
-
product
70 GHz Double Row Test Assembly
BE70A
The BE70A Series uses a single block design for ganged cabling and compression mount to the PCB, making it easier to install and eliminates soldering. The block consists of two rows, with up to 16 contacts, and is available for both microstrip and stripline transmission types. This proprietary cable design offers superior grounding (360-degree grounding with stripline) around a spring-loaded signal contact and provides a 1.85 mm connectors for RF device interfacing.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
Salt Spray Test Chamber
Dongguan Kejian Instrument Co., Ltd.
Corrosion resistance salt spray testing machine can be used to determine the corrosion resistance of inorganic or organic coatings of ferrous or non-ferrous metals, such as electroplating, anodizing, chemical processing, painting and other surface treatments.
-
product
Charge-to-Mass Ratio Test System
Model 212HS
Trek offers a unique, small, and portable Q/m analyzer which utilizes the "draw-off" toner transfer method to yield repeatable high accuracy toner charge measurements. The Trek Model 212HS Charge-to-Mass Ratio (Q/m) Test System is used to quickly and accurately determine the charge-to-mass ratio characteristics of both single and dual component electrophotographic toners and other charged particulates.
-
product
In-Circuit Test
TR5001T
The TR5001T Tiny 2 ICT is a new full feature In-Circuit board tester with a laptop sized footprint that provides a very cost effective alternative to large In-Circuit testers.
-
product
Universal Three-phase Protective Relay Test Set
Mentor-12
The Mentor 12 is the most advanced three-phase relay test set available for type and field testing of electromechanical and digital protections of any kind, in traditional or IEC-61850 based substations.
-
product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
product
Test Requirement Document for Developing and Documenting Strategy and Structure of Test Programs
TRD System
The TRD System helps users develop and document the strategy and structure of test programs using TRD format screens, flowchart generation tools and documentation formats, all in accordance with the most popular military standard format ( MIL-STD-1519) or with unique custom formats. It also has the ability to automatically generate an ATLAS test program from the TRD information provided by the user.
-
product
Test Lead Set
34138A
The Keysight 34138A test lead set for digital multimeters contains fixed sheath banana plugs. The Keysight 34138A is compatible with the 34460A, 34461A, 34401A, 34405A, 34410A, 34411A, L4411A, and U2741A digital multimeters. 34138a is not compatible with 3458A instead use 34137A with 3458A.
-
product
Test Automation Framework Design Services
This Services utilize uses a systematic, multi-stage approach to creating a framework for your organization.In simple terms, a framework defines the organization’s way of doing things.
-
product
Standalone Application
Origin Viewer
The Origin Vieweris a freely distributed, standalone application that allows viewing and copying of information contained in Origin project files and Origin window files, on computers that do not have Origin installed. This updated Viewer supports Origin's newest OPJU project file and window file (OGGU, OGWU, OGMU) formats, as well as the older OPJ and OGG, OGW, and OGM file formats.
-
product
TRIO Test System
*ICT FCT LED *Perfect & Cost Effective Technical Solution for Electronics manufacturers
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
product
Tecap Automated Test Suite
Control of Automated Test Equipment (ATE) for functional test and in-circuit testOperation of test facilities with adapters and PLCssemi- and fully automatic testing of electronic components and assembliesFinal Test in ProductionTest of pre-series and sample seriesStandardized test program developmentAdaptable to your own system environment (customizing) – 100% usable after installation with standard elements
-
product
Companion Tool to VS for Test Time & Pin reduction
UltraScan
UltraScan is SynTest's solution to combat increase in test time. In 130 nm or smaller ? nanometer geometries, many defects become delay defects and it becomes necessary to use delay tests to detect the transition faults and path delay faults. Often bridging tests are also required.
-
product
2-in-1 High-Voltage Test Hood
LX-HVE600EC
2-in-1 high-voltage test hood with integrated interchangeable setHV hood for electrical safety test & function test.The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate i...show more -
product
ElectroForce Cardiovascular Test Instruments
From bare metal stents to heart valves to pacemaker components, we offer the most comprehensive portfolio of cardiovascular device testing solutions. For more than 20 years, medical device manufacturers have trusted ElectroForce as the world leader in accelerated fatigue test instruments.
-
product
DMM Terminal Test Lead
U1580A
The Keysight U1580A test leads are compatible with the U1600A Series handheld digital oscilloscope probes and test leads. These test leads are used for the DMM terminal on the oscilloscopes.
-
product
Actuation Methods for In-Circuit Test Fixtures
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.